RM wraps Library.

Custom Printed Vinyl Wraps

Every order is custom-made to fix your subject.

  • Fixing Refrigerator Dents Before Wrapping with Bondo Spot Putty - RM wraps
    • 7/3/24

    Fixing Refrigerator Dents Before Wrapping with Bondo Spot Putty - RM wraps

    Fixing Refrigerator Dents Before Wrapping with Bondo Spot Putty

    Randy gives a brief demonstration of how we use Bondo Filler Putties to repair refrigerators and other surfaces before wrapping them, for an ultra-smooth and blemish-free wrapped finish. Most of the time these perfectly-good fridges would otherwise get returned and possibly thrown away, creating huge amounts of waste.

  • Bondo your cabinetry before wrapping it use 3M Di-noc Architectural film
    • 5/30/24

    Bondo your cabinetry before wrapping it use 3M Di-noc Architectural film

    Fixing some broke edges on the cabinetry before wrapping.

    Bondo your cabinetry before wrapping it use 3M Di-noc Architectural film.

    How to Use Bondo on Cabinet Edges Before Wrapping with Architectural Film

    Introduction

    In this tutorial, we'll show you how to repair and prepare the edge of a cabinetry piece using Bondo before wrapping it with an architectural film. This method is especially useful when there's a chunk of wood missing, as Bondo can be shaped to form a clean corner and provides a hard surface for the film to adhere to.

    Materials Needed

    Bondo

    Hardener (usually comes with the Bondo)

    Putty knife

    Sandpaper (various grits)

    Clean cloth

    Masking tape (optional)

    Architectural film

    Squeegee or application tool

    Step-by-Step Instructions

    Step 1: Prepare the Area

    Clean the Surface: Ensure the edge of the cabinetry is clean and free of dust, dirt, and grease. Use a clean cloth to wipe the area.

    Masking (Optional): If you want to protect the surrounding areas from Bondo, use masking tape around the edge where the repair will be made.

    Step 2: Mix the Bondo

    Read Instructions: Follow the manufacturer's instructions for mixing Bondo and hardener. Typically, you'll mix a small amount of hardener with the Bondo until you achieve a uniform color.

    Mix Thoroughly: Use a putty knife to mix the Bondo and hardener on a clean, non-porous surface. Work quickly, as Bondo can start to harden within minutes.

    Step 3: Apply the Bondo

    Apply to the Edge: Using the putty knife, apply the mixed Bondo to the damaged edge of the cabinetry. Overfill slightly to ensure you have enough material to shape a clean corner.

    Shape the Edge: While the Bondo is still pliable, shape it into a clean corner. You can use the putty knife to smooth and form the desired shape.

    Step 4: Let it Cure

    Allow to Dry: Let the Bondo cure completely. This typically takes about 20-30 minutes, but check the manufacturer's instructions for specific curing times.

    Step 5: Sand the Surface

    Sand Smooth: Once the Bondo is fully cured, use sandpaper to smooth the surface. Start with a coarser grit to remove excess material and then switch to a finer grit for a smooth finish.

    Clean the Area: Wipe away any dust created during sanding with a clean cloth.

    Step 6: Apply the Architectural Film

    Prepare the Film: Measure and cut the architectural film to the appropriate size for the cabinetry edge.

    Apply the Film: Starting from one end, carefully apply the film to the edge, using a squeegee or application tool to smooth out any bubbles or wrinkles. Make sure the film adheres well to the Bondo-repaired edge.

    Finish the Edges: Trim any excess film and ensure all edges are securely adhered.

    By following these steps, you can effectively repair and prepare cabinetry edges with Bondo before wrapping them with architectural film. This method ensures a smooth, clean corner that enhances the adhesion and appearance of the film.

    See more patterns here. https://www.rmwrapsstore.com/